RCModelScout.

ReadyMadeRC

FY-41AP-A AIRPLANE STABILIZER, AUTOPILOT, AND ON SCREEN DISPLAY

Flight stabilization is achieved via an integrated 3 axis gyro, 3 axis accelerometer, 3 axis magnetometer and a barometric pressure sensor. This enables the module to accurately measure flight attitude, earth azimuth & relative altitude to achieve:, - Extremely stable conventional flight pattern, > Related download for fix-wing :, Reminder from Feiyu-tech: You should to do the firmware upgrade separately for FY-41AP-OSD control module and OSD module. UART1 is the interface connects to the data radio, PC computer serial port to do the firmware upgrade for FY-41AP control module.If you want to upgrade the firmware of FY-41AP OSD module,please, Integrated OSD Video Overlay System, FY-41AP overlays flight telemetry information onto video image. Information displayed includes: Altitude, Speed, Direction, Home Direction and many more., Feiyu tech kindly remind you: You should to do the firmware upgrade separately for FY-41AP-OSD control module and OSD module. UART2 is the interface connects to the PC computer serial port to do the firmware upgrade for FY-41AP OSD module.If you want to upgrade the firmware of  flight control part ,please, :, 1, Normal / Traditional fixed-wing planes;, Assistant Software System Require,

ReadyMadeRC

EASY STAR/SKY SURFER/BIXLER ADJUSTABLE MOTOR MOUNT

Three step installation:, , Included:, 1 - Motor Base Tube and Motor Plate, 4 motor screws and 4 mount screws., Notes:, A 35mm outrunner motor will only fit in Position 3 (+ 1.0"). 28mm outrunners will work in any of the three positions. The stock thrust angles are retained in all 3 positions. If a change in thrust angle is desired, simply add a small washer between the motor base and motor plate at the appropriate locations., Compatible Motors:, , Acceptable bolt patterns (units in mm):, 16x16, 16x19, 19x19, 19x25, 25x25,

ReadyMadeRC

SZD-45 OGAR (PRE-ASSEMBLED COMBO)

ReadyMadeRC

SZD-45 OGAR (KIT)

Requires : Brushless Outrunner Motor, 4 Micro Servos, Propeller Adaptor, 4-channel+ radio, 20A+ brushless ESC, 3 cells 11.1V 15C 1800mAh Li-Po battery or larger capacity,  and charger, CA Glue for assembly,

ReadyMadeRC

SKY SURFER PNP BRUSHLESS (1.4M)

*Note: There are people looking at what they are calling "version 1" and "version 2" of this plane.  They really aren't version 1 or 2, but they are just different versions of this plane.  Mine are what people are calling version 1, just as the pictures show.  This is MUCH better for FPV since there is a ton of space inside the fuselage.  The "version 2" planes ruined the usefulness for FPV by putting the servos and control arms inside the fuselage.  The tubes for the control arms add strength to the fuselage in this version.  My store is focused on FPV, so the equipment I carry will be what is best for FPV!, *Not to be distributed or linked to by other companies who like to take other people's work.  You know who you are... :),

ReadyMadeRC

SUPER SKY SURFER 2000 ADJUSTABLE MOTOR MOUNT

Three step installation:, Install base tube into the plastic nacelle and secure in place with the 4 socket head screws (allen wrench included), Included:, 1 - SSS 2000 Base Tube and SSS Motor Plate, 4 motor screws, 4 motor plate screws,  4 base tube socket head screws, 1 allen wrench., Notes:, The stock thrust angles are retained in all 4 positions. If a change in thrust angle is desired, simply add a small washer between the motor base and motor plate at the appropriate locations., Acceptable bolt patterns (units in mm):, 19x19,

ReadyMadeRC

HITEC SKYSCOUT KIT (EASY STAR 2) AIRFRAME AND PLASTIC PARTS

SPECIFICATIONS:, , Includes:,

ReadyMadeRC

CC3D OPENPILOT COPTERCONTROL BOARD BY READYMADERC

CC3D from the OpenPilot project introduces a hardware refresh of the highly regarded multi-purpose aircraft stabilization platform. The CopterControl platform has been designed from the ground up to perform the following functions:, A MultiRotor controller with auto-level, including TriCopters, QuadCopters and HexaCopters, The CopterControl hardware has the following features:, Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM, For info:,

ReadyMadeRC

DJI NAZA H - HELICOPTER STABILIZATION CONTROLLER

ReadyMadeRC

GOPRO-HOUSING "SNAP" V2.0 FOR GOPRO HD2 - WHITE

Most important changes:, - Screw-mechanism instead of the snapping mechanism (details see below), All functions together:, , Screw-Mechanism for a complete protection and a stable mounting:, With version 1 there was a snapping mechanism which was also responsible for the name. The mechanism was very easy to use, but has proven to be not as secure as i wanted it to be. There have been crashes reported where the front plate just flew off, which drastically reduces the safety of your GoPro. The search was long for the best mounting option, but finally a screwing solution has proven to be best. By using specially designed knurled screws, the GoPro can be removed just as easy on the field as with the snapping mechanism, and no tools are needed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the widely available replacement lenses (for the skeleton-housing). It does not need to be glued in, but instead is being hold perfectly tight by 3 nylon screws. This way the lens can be used in different front-plates and/or housings., :, By using 3 countersunk screws and some of the multiple mounting holes, the housing can be mounted very flexible on almost anything., :, "Snap" can be easily installed/uninstalled on the Eyefly frames. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video)., :, The front-plate allows the usage of different front-plates for different use-cases. The front-plate included in the standard housing is made for installing just the GoPro and nothing else. By using the, A short mounting manual::, 1) Put together "dry", without glueing, to make sure you've got everything right (including GoPro!),

ReadyMadeRC

GOPRO-HOUSING "SNAP" V2.0 FOR GOPRO HD2 - BLACK

Most important changes:, - Screw-mechanism instead of the snapping mechanism (details see below), All functions together:, , Screw-Mechanism for a complete protection and a stable mounting:, With version 1 there was a snapping mechanism which was also responsible for the name. The mechanism was very easy to use, but has proven to be not as secure as i wanted it to be. There have been crashes reported where the front plate just flew off, which drastically reduces the safety of your GoPro. The search was long for the best mounting option, but finally a screwing solution has proven to be best. By using specially designed knurled screws, the GoPro can be removed just as easy on the field as with the snapping mechanism, and no tools are needed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the widely available replacement lenses (for the skeleton-housing). It does not need to be glued in, but instead is being hold perfectly tight by 3 nylon screws. This way the lens can be used in different front-plates and/or housings., :, By using 3 countersunk screws and some of the multiple mounting holes, the housing can be mounted very flexible on almost anything., :, "Snap" can be easily installed/uninstalled on the Eyefly frames. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video)., :, The front-plate allows the usage of different front-plates for different use-cases. The front-plate included in the standard housing is made for installing just the GoPro and nothing else. By using the, A short mounting manual::, 1) Put together "dry", without glueing, to make sure you've got everything right (including GoPro!),

ReadyMadeRC

GOPRO-"SNAP" HOUSING FOR GOPRO HERO3 - BLACK

All functions together:, , Screw-Mechanism for a complete protection and a stable mounting:, With the first hero1&2-version there was a snapping mechanism which was also responsible for the name. The mechanism was very easy to use, but has proven to be not as secure as i wanted it to be. There have been crashes reported where the front plate just flew off, which drastically reduces the safety of your GoPro. The search was long for the best mounting option, but finally a screwing solution has proven to be best. By using specially designed knurled screws, the GoPro can be removed just as easy on the field as with the snapping mechanism, and no tools are needed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the 2 lens-options. It does not need to be glued in, but instead is being hold perfectly tight by 3 polyamide screws., :, By using 3 countersunk screws and some of the multiple mounting holes, the housing can be mounted very flexible on almost anything., :, "Snap" can be easily installed/uninstalled on the Eyefly frames. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video)., :, The front-plate allows the usage of different front-plates for different use-cases. The front-plate included in the standard housing is made for installing just the GoPro and nothing else. By using the "duo"-adapter, also available in the shop, you can mount a CCD-cam in addition to the GoPro without an issue., A short mounting manual::, 1) Put together "dry", without glueing, to make sure you've got everything right (including GoPro!),

ReadyMadeRC

GOPRO-"SNAP" HOUSING FOR GOPRO HERO3 - WHITE

All functions together:, , Screw-Mechanism for a complete protection and a stable mounting:, With the first hero1&2-version there was a snapping mechanism which was also responsible for the name. The mechanism was very easy to use, but has proven to be not as secure as i wanted it to be. There have been crashes reported where the front plate just flew off, which drastically reduces the safety of your GoPro. The search was long for the best mounting option, but finally a screwing solution has proven to be best. By using specially designed knurled screws, the GoPro can be removed just as easy on the field as with the snapping mechanism, and no tools are needed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the 2 lens-options. It does not need to be glued in, but instead is being hold perfectly tight by 3 polyamide screws., :, By using 3 countersunk screws and some of the multiple mounting holes, the housing can be mounted very flexible on almost anything., :, "Snap" can be easily installed/uninstalled on the Eyefly frames. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video)., :, The front-plate allows the usage of different front-plates for different use-cases. The front-plate included in the standard housing is made for installing just the GoPro and nothing else. By using the "duo"-adapter, also available in the shop, you can mount a CCD-cam in addition to the GoPro without an issue., A short mounting manual::, 1) Put together "dry", without glueing, to make sure you've got everything right (including GoPro!),

ReadyMadeRC

OPENPILOT REVOLUTION FLIGHT CONTROLLER

For info:,

ReadyMadeRC

CC3D OPENPILOT COPTERCONTROL BOARD BY READYMADERC (RIGHT ANGLE)

CC3D from the OpenPilot project introduces a hardware refresh of the highly regarded multi-purpose aircraft stabilization platform. The CopterControl platform has been designed from the ground up to perform the following functions:, , The CopterControl hardware has the following features:, , For info:,