ReadyMadeRC
TAROT 2 AXIS CAMERA GIMBAL FOR GOPRO HERO3, 3+ W/FREE CABLE
| 7. Supported receiver type | conventional/S-BUS/DSM2/DSMJ/DSMX receiver. |
| 8. Supported RC | PPM/PCM/2.4G. |
| 9. Operating supply | DC 7.4V~14.8V (Li-Po 3S is recommended) |
| 10. Operating current | 200mA-500mA (Depending on power supply voltage and motor power) |
| 11. Operating temperature | -15ºC~65ºC. |
| 12. CPU | Double 32bit ARM |
| 13. Sensor technology | 3-axis MEMS gyro and accelerometer. |
| 14. Max angular rate | 2000 º /sec. |
| 15. Max acceleration | 16g. |
| 16. Control frequency | 2000Hz |
| 17. Motor driver frequency | 20KHz (quiet and smooth) |
| 18. Control accuracy | 0.1° |
| 19. Control range | -45º~45º(roll), -135 º~90 º(tilt). |
| 20. Attitude arithmetic | BLDC gimbal dedicated brushless motor decoupled EKF algorithm. |
| 21. Aerial photography equipment | GOPRO Hero3. |
Note:, Modifications may be required to use HERO4, Parts included for the kit: 2 motors mounted onto the swing arms, gimbal controller board, mounting bracket with GoPro brace, 2 male to male servo cables (one with Y end), USB firmware updater connector and cable, 4 rubber dampeners and mounting bracket + hardware for the gimbal.,
FREE LIVE VIDEO OUT CABLE OPTION...YES, OUR CABLES WILL WORK ...ReadyMadeRC
DRONE FRAMES - G-10 DRQ250 "MINI-D" - GLASS FIBER
| Flight Controller | Naze32 Acro |
| HD Camera | Mobius |
| Frame weight | 138-145 grams |
From Ubay at Drone Frames:, The “Mini D” is a Clean/Dirty plate design separated by M3 dampers that allows you to take jello-free videos with your HD camera. I have flown it numerous times now but have never had any "jello" issues. So, what makes this frame different?, 3 different thickness of G10 plates were used:, , Different Variables for FPV/REC camera:, , Recommended Equipment:, Motors:, Tiger MN 1806 2300kv (3s-4s), :Gemfan 10A, Prop:, 2 blade 5030 Gemfan, 2 Blade 5 x 4 HQ Composite, 2 Blade 6030 HQ Composite,
Arms - 3mm thickness and individual, so very easy to ...ReadyMadeRC
DRONE FRAMES - CF DRQ250 "MINI-D" - CARBON FIBER
| Flight Controller | Naze32 Acro |
| HD Camera | Mobius HD cam or GoPro Hero 3 |
| Frame weight | 125 grams |
From Ubay at Drone Frames:, The “Mini D” is a Clean/Dirty plate design separated by M3 dampers that allows you to take jello-free videos with your HD camera. I have flown it numerous times now but have never had any "jello" issues. So, what makes this frame different?, 3 different thickness of carbon fiber plates were used:, , Different Variables for FPV/REC camera:, , Recommended Equipment:, Motors:, Tiger MN 1806 2300kv (3s-4s), :Gemfan 10A, Prop:, 2 blade 5030 Gemfan, 2 Blade 5 x 4 HQ Composite, 2 Blade 6030 HQ Composite,
CF version of the DRQ 250 is structurally the same ...ReadyMadeRC
FUIM3 USB INTERFACE MODULE FOR 2-WAY DATA COMMUNICATION
,
This high speed, opto-isolated, PC USB interface module is designed ...ReadyMadeRC
FY-40A INERTIAL FLIGHT STABILIZATION SYSTEM
| Mode 1 | Deactivated Mode |
| Mode 2 | Stabilized Mode |
| Mode 3 | 3D Mode |
| Supported servo output | 50Hz refresh frequency |
| Recommended Transmitter | PCM or 2.4GHz with minimum 5 channels |
| Working Voltage Range | DC 4.8V~5.5V (0.05A@5V, Powered by ESC) |
| Operating Temperature | -20°C ~ 50°C |
| Max Gyro Angular Velocity | 2000°/s |
| Weight&Dimensions | FY-40A 17g(45mm x 30mm x 9 mm) |
has an integrated three-axis gyro and three-axis accelerometer which controls the aircraft movement in three-dimensional space. Installation is very simple.By using your remote control, the unit can be turned on or off for the following functions:, Supported aircraft :, , Specifications:, ,
FY-40A ——In this mode, the FY-40Aauto stabilization is turned off. ...ReadyMadeRC
GOPRO-"SNAP" HOUSING FOR GOPRO HERO3 - CARBON FIBER
| Weight of the housing includingg screws and lens protection | 30 grams |
| Disclaimer | I suggest clipping off one side of the nut a bit, so there won't be any part of it that would |
All functions together:, , Screw-Mechanism for a complete protection and a stable mounting:, With the first hero1&2-version there was a snapping mechanism which was also responsible for the name. The mechanism was very easy to use, but has proven to be not as secure as i wanted it to be. There have been crashes reported where the front plate just flew off, which drastically reduces the safety of your GoPro. The search was long for the best mounting option, but finally a screwing solution has proven to be best. By using specially designed knurled screws, the GoPro can be removed just as easy on the field as with the snapping mechanism, and no tools are needed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the 2 lens-options. It does not need to be glued in, but instead is being hold perfectly tight by 3 polyamide screws., :, By using 3 countersunk screws and some of the multiple mounting holes, the housing can be mounted very flexible on almost anything., :, "Snap" can be easily installed/uninstalled on the Eyefly frames. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video)., :, The front-plate allows the usage of different front-plates for different use-cases. The front-plate included in the standard housing is made for installing just the GoPro and nothing else. By using the "duo"-adapter, also available in the shop, you can mount a CCD-cam in addition to the GoPro without an issue., A short mounting manual::, 1) Put together "dry", without glueing, to make sure you've got everything right (including GoPro!),
This GoPro-housing offers a perfect protection of your GoPro against ...ReadyMadeRC
CC3D ATOM OPENPILOT COPTERCONTROL BOARD BY RMRC (RIGHT ANGLE)
| Note | We recommend |
CC3D from the OpenPilot project introduces a hardware refresh of the highly regarded multi-purpose aircraft stabilization platform. The CopterControl platform has been designed from the ground up to perform the following functions:, , The CopterControl hardware has the following features:, , For info:,
updating your controller to 14.10 release, especially for mini quads ...ReadyMadeRC
CC3D ATOM OPENPILOT COPTERCONTROL BOARD BY RMRC (STRAIGHT PINS)
| Note | We recommend |
CC3D from the OpenPilot project introduces a hardware refresh of the highly regarded multi-purpose aircraft stabilization platform. The CopterControl platform has been designed from the ground up to perform the following functions:, , The CopterControl hardware has the following features:, , For info:,
updating your controller to 14.10 release, especially for mini quads ...ReadyMadeRC
RMRC FPV FEST REGISTRATION - SEPTEMBER 8TH-11TH, 2016
| Run What U Brung | Any mulitrotor regardless of cells or props. |
| Beginner | Any mulitrotor regardless of cells or props. |
| Run What U Brung | Any fixed wing aircraft regardless of cells or props. |
| Beginner | Any fixed wing aircraft regardless of cells or props. |
| NOTE | If you make a reservation and wish to cancel, |
Location of Event:, Willard Municipal Airport, Note: This airport will be closed to full scale aviation for the duration of the event. If you wish to fly your full scale aircraft to FPV Fest, you will need to arrive well, Lodging Information:, , Camping Information:, If you are planning on camping at the airport, please choose the appropriate drop down option below. The venue does not have any hook-ups available, including electricity and water. Porta-johns will be on site, however. We will have a, Dining Options:, We have scheduled for a local food truck to be available during the peak hours throughout the event. Of course you are also welcome to grill out at your camping location. Other available options are shown in the map below:, , Manufacturers and Organizations Attending FPV Fest:, , Retail Vendors available at FPV Fest:, , The purpose of this fly-in is for folks to be able to hang out and enjoy some fun FPV together, make some new friends, and learn a little at the same time. Please do your part and keep it fun! :),
Welcome to the 3rd annual Ready Made RC FPV Fest! ...ReadyMadeRC
RMRC ANACONDA - KIT
| Wingspan | 2,060mm |
| Wing Area | Approx. |
| Length | 1,410mm |
| Motor | 35-48 800-1000kv Brusless outrunner |
| Propeller | 13x6.5 E or 14x5.5 E (Not included) |
| ESC | 60-80A ESC with switch mode BEC |
| Servos | 3x 30g and 2x 17g Metal Gear Digital |
| Flap servos | HS-81 |
| Battery | Li-Po 4s 5,000mAH - 20,000mAH (Additional nose weight needed with smaller batteries) |
| Center of Gravity | 1/3 of wing from leading edge at the main spar |
| Approximate flight duration | 45 minutes to over an hour depending on configuration |
| Fuselage dimensions (Inside) | L 66cm (26.5") x W 15cm (6") x H 8cm (3") |
| RcGroups.com Unboxing Video with Jim Graham | (PNP version shown) |
Features:, , Specifications:, , Control:, Width, Looking inside the fuselage:, , Notes:,
Anaconda KIT After months of testing, we are proud to ...ReadyMadeRC
RMRC ANACONDA - PNP (WITH INSTALLED MOTOR, ESC, AND SERVOS)
| Wingspan | 2,060mm |
| Wing Area | Approx. 4,900cm |
| Length | 1,410mm |
| Motor | RMRC Tiger Motor Brushless Outrunner AT3520-5, 800kv (6mm prop adapter shaft) |
| Propeller (sold separately) | Recommend |
| ESC | RMRC Tiger Motor 80A ESC with switch mode BEC (T-Plug connector) |
| Servos | 3x 30g and 2x 17g Metal Gear Digital (does not include 2x servos for flaps) |
| Recommended Flap servos | HS-81 |
| Battery | Li-Po 4s 5,000mAH - 20,000mAH (Additional nose weight needed with smaller batteries) |
| Center of Gravity | 1/3 of wing from leading edge on the main spar |
| Approximate flight duration | 45 minutes to over an hour depending on configuration |
| Fuselage dimensions (Inside) | L 66cm (26.5") x W 15cm (6") x H 8cm (3") |
Features:, , Specifications:, , RMRC's Setup for the Anaconda:, , RcGroups.com Unboxing Video with Jim Graham:, , Looking inside the fuselage:, , Notes:, , Can be broken down for transport:, Picture courtesy of ducatirdr from RCGroups.com,
Anaconda PNP - with installed Motor, ESC, and Servos After ...ReadyMadeRC
200 QX BNF WITH SAFE
| Type | Quad-Copter |
| Main Rotor Diameter | 4.45 in (113mm) |
| Length | 5.59 in (142mm) |
| Kit/ARF/RTF | BNF |
| Experience Level | Intermediate |
Is Assembly Required: No,
Features SAFE™ Technology equipped Three flight modes High performance brushless ...ReadyMadeRC
CARBON-Z CUB BNF BASIC
| Wingspan | 84.6 in (215 cm) |
| Overall Length | 55.8 in (142 cm) |
| Wing Area | 1100 sq. in. (71.0 sq. dm.) |
| Flying Weight | 8.15 lb (3.70 kg) |
| Motor Size | 50-size brushless outrunner (installed) |
| Radio | 6+ channel DSM2/DSMX transmitter (required) |
| Servos | (4) 26-gram MG mini servos, (2) 13-gram micro servos (installed) |
| CG (center of gravity) | 4.72 in (120mm) back from leading edge of wing |
| Wing Loading | 17 oz/sq ft |
| Prop Size | 15 x 5.5 Electric (included) |
| Speed Control | 60-amp brushless (installed) |
| Recommended Battery | 22.2V 6S 3200mAh LiPo (required) |
| Flaps | Yes |
| Approx. Flying Duration | 7 minutes |
| Minimum Age Recommendation | 14 years |
| Experience Level | Intermediate |
| Recommended Environment | Outdoor |
| Assembly Time | Less than 1 Hour |
| Is Assembly Required | Yes |
| Spinner Size | 2.64 in (67mm) |
Optional Accessories:, - Float set (EFL1045016), Retracts: No,
Features Easy-to-complete final assembly Quique Somenzini design and attention to ...ReadyMadeRC
PARKZONE ARCHER BNF
| Wingspan | 36.8 in (935mm) |
| Overall Length | 25.6 in (650mm) |
| Flying Weight | 16.4 oz (466 g) |
| Motor Size | 370-size 1300Kv brushless outrunner (installed) |
| Radio | AR400 4-channel receiver (installed) |
| Trim Scheme Colors | Red, grey, black and white |
| CG (center of gravity) | 1.6 in (40mm) back from the leading edge of wing |
| Prop Size | 8.25 x 5.5 |
| Spinner Size | 1.0 in (25mm) |
| Speed Control | 10-amp (installed) |
| Recommended Battery | 7.4V 2S 1300mAh 20C Li-Po (included) |
| Charger | 2S DC Li-Po balancing charger (included) |
| Minimum Age Recommendation | 14 years |
| Experience Level | Intermediate |
| Recommended Environment | Outdoor |
| Assembly Time | Less than 1 Hour |
| Is Assembly Required | Yes |
Flaps: No, Retracts: No,
Features 4-channel control—throttle, elevator, aileron and rudder Powerful 370-size, 1300Kv ...ReadyMadeRC
PARKZONE - MOSQUITO MK VI BNF PKZ6350
| Wingspan | 1244mm (49.0 in) |
| Overall Length | 955mm (37.6 in) |
| Flying Weight | 42.3 oz (1200 g), 44.4 oz (1260 g) with flaps servos and retracts installed |
| Motor Size | (2) 370-size brushless outunner |
| Radio | 4+ channel (6+ channel for optional retracts and flaps) required |
| Servos | (2) DSV130 and (2) SV80 servos (installed) |
| CG (center of gravity) | 2.90-3.30 (73-83mm) back from the leading edge of wing at fuselage |
| Prop Size | 8.25 x 5.5 |
| Speed Control | (2) 18-amp brushless (installed) |
| Recommended Battery | 11.1V 3S 2200mAh 25C LiPo (required) |
| Flaps | Optional (servo |
| Retracts | Optional (EFLG100) |
| Control Throw (Ailerons) | Low |
| Control Throw (Elevator) | Low |
| Control Throw (Rudder) | Low |
| Control Throw (Flaps) | Half |
| Minimum Age Recommendation | 14 years |
| Experience Level | Intermediate |
| Recommended Environment | Outdoor |
| Assembly Time | Less than 1 Hour |
| Is Assembly Required | Yes |