HobbyKing
REAR WHEEL SHAFTS - A2032 AND A2033 (2PCS)
,
Rear Wheel Shafts - A2032 and A2033 (2pcs)5 Reviews
HobbyKing
STEERING BLOCK BALL-HEADED SCREWS - 1/10 TURNIGY GT-10X PAN CAR (4PCS)
,
Steering Block Ball-Headed Screws - 1/10 Turnigy GT-10X Pan Car ...HobbyKing
METAL MOTOR MOUNT B - 1/10 TURNIGY GT-10X PAN CAR
,
Metal Motor Mount B - 1/10 Turnigy GT-10X Pan CarHobbyKing
SELF-TAPPING SCREWS (M3*8MM) - TURNIGY GT-10X PAN CAR (16PCS)
,
Self-Tapping Screws (M3*8mm) - Turnigy GT-10X Pan Car (16pcs)HobbyKing
EG SPORT 21 TWO STROKE GLOW ENGINE FOR CAR
| Displacement | 3.45CC |
| Bore | 16.26mm |
| Stroke | 16.80mm |
| Carburetor | 8mm |
| Crankshaft | 14mm SG |
| RPM | 6,000~36,000 |
| Maximum Power | 2.6hp |
| Weight | 397g |
Features:, • ABC construction, Aluminum piston with Brass liner that's Chrome plated, Ports:3,
Tired of all those electric cars infesting your local R/C ...5 Reviews
HobbyKing
AQ-600 QUADCOPTER FRAME - REPLACEMENT ARM W/MOTOR MOUNT (BLACK)
,
AQ-600 Quadcopter Frame - Replacement Arm w/Motor Mount (Black)HobbyKing
1/10 QUANUM SKULL CRUSHER 2WD BRUSHLESS MONSTER TRUCK (RTR)
| Length | 467mm |
| Wheeltrack | 325mm |
| Wheelbase | 274mm |
| Tire Size | 136x71mm |
| Wheel Diameter | 82mm (12mm hex) |
| Gear Ratio | 10.86 |
Features:, • Completely ready to run with power system, steering servo and 2.4gHz radio system pre-installed, Specs:, Battery Tray Size:, 140L x 48W x 34H (mm), ESC:, 35A (190A burst) brushless (pre-installed, Motor:, 3650 size 2700KV brushless inrunner (pre-installed), Servo:, High-torque standard size (pre-installed), Includes:, Quanum Skull Crusher 1/10 Monster Truck, Requires:, 2S 3300~5000mAh lipoly battery pack,
Are you ready for the ultimate in bone breaking, car ...5 Reviews
HobbyKing
"HARD ONE" 1.0M HARDENED HELICOPTER PINION GEAR 6MM SHAFT - 11T
Note:, If you have a Neu Motor - Neu motor shafts are .05mm over size. The solution to this is to run the motor at low rpm and touch a piece of 400 grit sand paper against the shaft for a couple of seconds. Then the pinions fit perfectly.,
"Hard One" 1.0M Hardened Helicopter Pinion Gear 6mm Shaft - ...HobbyKing
WHEEL HUB - 1/10 QUANUM VANDAL 4WD RACING BUGGY (4PCS)
,
Wheel Hub - 1/10 Quanum Vandal 4WD Racing Buggy (4pcs)HobbyKing
SWAY BAR HOLDERS - 1/10 QUANUM VANDAL 4WD RACING BUGGY (6PCS)
,
Sway Bar Holders - 1/10 Quanum Vandal 4WD Racing Buggy ...HobbyKing
FLAT HEAD HEX M3*10 - 1/10 QUANUM VANDAL 4WD RACING BUGGY (5PCS)
,
Flat Head Hex M3*10 - 1/10 Quanum Vandal 4WD Racing ...5 Reviews
HobbyKing
"HARD ONE" 0.7M HARDENED HELICOPTER PINION GEAR 5MM SHAFT - 18T
Note:, If you have a Neu Motor - Neu motor shafts are .05mm over size. The solution to this is to run the motor at low rpm and touch a piece of 400 grit sand paper against the shaft for a couple of seconds. Then the pinions fit perfectly.,
"Hard One" 0.7M Hardened Helicopter Pinion Gear 5mm Shaft - ...HobbyKing
BOSCAM 5.8GHZ DIVERSITY RECEIVER 7.0 INCH TFT LCD MONITOR FOR FPV 800X480 LED BACKLIGHT
| Working Frequencies | CH1 |
| CH2 | 5685MHz |
| CH3 | 5665MHz |
| CH4 | 5645MHz |
| CH5 | 5885MHz |
| CH6 | 5905MHz |
| CH7 | 5925MHz |
| CH8 | 5945MHz |
| Screen Size | 7.0 inch |
| Screen Type | TFT LCD |
| Backlight Type | LED |
| Resolution | 800 x 480 |
| Brightness | 450cd/m² |
| Contrast | 500 |
| Working Temperature | -10°C ~ +65°C |
| Power Consumption | < 8W |
| Size | 180 x 120 x 23mm |
| Antenna connection | SMA |
Features:, • 800 x 480 High Resolution TFT LCD Screen, Specs:, View Angle:, 140/120° (Horizontal/Vertical), Working Voltage:, DC 7~12V or 11.1V lipoly battery, Included in box:, 7.0 inch 5.8GHz Diversity TFT LCD monitor,
This 5.8GHz Diversity LCD Screen offers the perfect solution for ...5 Reviews