|Hardware frequency Range||400MHz to 470MHz|
|Output low-pass Filter||NONE|
|Low rate||40Hz @10Kbps|
|High rate||66Hz @15Kbps|
|RF interface impedance||50 Ohm|
|Supply Voltage||8.4V to 16V|
|Reverse battery protection||NONE|
|Frequency Range||400MHz to 470MHz|
|F/S turn on condition||>0.99EBR|
|Response Time||4mS to 25mS|
|PWM Output range||0.5mS-2.5mS|
|Recommend Supply Voltage||3.5V to 8.4V|
|Shutdown voltage||3 V|
|Reverse breakdown voltage||>-15V|
|Output ports withstand voltage||>12V|
|Operating Temperature||–40 to +80 °C|
|Low frequency Power supply noise filter||Include|
|High frequency noise filter||Include|
Included in box:, TS4047 transmitter module (JR style), TS4047 Module Specifications:, Channel :70, Frequency Range:, 433.05MHz -434.79MHz, Channel:70, Low Output Power:, 30DB -31DB Peak (0.9W-1.2W), High Output Power:, 33DB -34DB Peak (1.9W-2.5W), Current:, 330mA/520mA (@50 Ohm load,12V Supply Voltage), Temperature:, 50 to 70 Degrees Celsius, RD4047P Receiver Specifications:, Sensitivity :, -112 DBM @0.1EBR(40Hz Refresh rate)(10Kbps low rate ), PWM Output accuracy:, 0.5uS step ERROR<20PPM, PWM output cycle:, 55Hz @Normal mode / 192Hz @Fast mode, PPM Output accuracy:, 0.5uS step ERROR<20PPM, PPM Output range:, 0.5mS-2.5mS Each channel, PPM output cycle:, 50Hz@Normal mode & 1mS to 2mS Output, PPM sync pulse width:, 4mS to 16mS Automatic adjust @Normal mode / 4mS unchanging @Fast mode, RSSI output range:, 0-3.3V (RF signal weak <0.8V),The RMILEC TS4047 10CH 2.5W UHF Module System offers the ...
|Range||Full range system|
Features:, • 3.3v FTDI support for easy programming (, Specs:, Compatibility:, 5-pin JR compatible module-based transmitters, IC:Atmega328P, Includes:, OrangeRx OpenLRS Tx Module (JR/Turnigy compatible), *Note:, The setup and use of Open LRS requires computer programming skills and basic Arduino experience. This is not a "plug and play" system. See the attached document under the "Files" tab for resources on programming info, firmware downloads and more., : Open LRS uses 3.3v FTDI support,,The all new OrangeRX Open LRS TX Module is an ...
Specs:, Channels:3, NOTE:, 1) This is not a Spektrum receiver, nor is it a copy of a Spektrum Receiver.,Compatible with all Spektrum DSM2 ground transmitters. Orange Rx receivers ...
The UltraPAC range of memory modules is fully compatible with the following transmitter sets:, Futaba 9Z, 9ZWC, 9ZWC2 (a.k.a. ZAP/ZHP), Features:, Equipped with a large memory capacity giving you the equivalent of up to eight individual 64K CAMPacs,SpartanRC Futaba 512K Ultra Pac II Spartan RC has developed ...
|Futaba||3PM, 3PK, 7U, 8U,8J, 9C, 10C, 9Z, FN-Series, T10C, FC-18, FC-28.|
|Hitec||Optic 6, Eclipse 7, Prism 7|
|Dimensions||44 x 24 x 14 mm|
|Operating voltage||6.0V-13.0V (can handle 3S!)|
Features:, Advanced Continuous Channel Shifting Technology (ACCST is our advanced tecnology it shifts channel hundred times per second and there is no signal conflicts and interruptions) robust frequency agility., Transmitter Module is compatible with the following transmitters:, DFT:, Receiver Specification:, Number of channels: 8, Module specification:, Output Power:: 60mW,FrSKY ACCST technology is proven, approved by many model associations, ...
Channels:, 4 (Support up to 5 channels with “Mul-CH”), ESC:, 2A integrated Brushed, Size:, 21.40mm x 12.00mm x 6.00mm, Weight:, 0.8g ï¼ˆnot including wiresï¼‰, Voltage:, 3.0V~5.0V ï¼ˆ1S Lipoly recommendedï¼‰,The 2.4ghz SuperMicro All-in-one unit combines a receiver and 2A ...
|Latency||18ms (FS) 9ms (HS)|
|Compatible with FrSky 2 way telemetry modules||DFT, DJY, DHT, DHT-U|
Features:, Advanced Continuous Channel Shifting Technology (ACCST is our advanced tecnology it shifts channel hundred times per second and there is no signal conflicts and interruptions) robust frequency agility., Receiver Specification:, Number of channels: 6,FrSKY ACCST technology is proven, approved by many model associations, ...
|Number of Channnel||8ch ppm/9ch pcm|
|Low Voltage Show||Yes|
Support user:8, Stick model:4, Required:, Battery, Included:, Turnigy 9x 9Ch Transmitter, NOTE: "SWITCH ERROR" means you have one of the switches in the wrong position when you turn the radio on. It is not a fault.,With v2 firmware update, correcting many flaws of the previous ...