RCPlanet
O.S. ENGINES 30VG ES ELECTRIC STARTER OSM13966
, Displacement:, 0.298 cu in (5.0cc), Bore:, 0.728" (18.5mm), Stroke:, 0.717" (18.2mm), Practical RPM:, 4,000-36,000, Power Output:, 3.0 PS, 2.96 HP/28,000 RPM, Weight:, 12.7oz (360g), Crankshaft Size:, 1/4-28, Factory Needle Valve Setting:, 2-3/4 turns OPEN from fully closed, Mixture Control Valve Setting:, Needle head flush with the side of ball link housing then back in 1-1/2 turn, Distance Between Mounting Holes Same Side:, 0.83" (21mm), Distance Between Mounting Holes Opposite Side:, 1.4" (37mm), Distance Between Mounting Holes Diagonal:, 2.3" (59mm), Height Bottom of Mounting Tabs to Top of Cylinder Head:, 3.8" (97.7mm), Width of Mounting Tabs:, 1.8" (45mm), Width of Crankcase Below Mounting Ears:, 1.2" (30.8mm), Distance from Front Bearing to end of Crankshaft:, 1.2" (29.5mm), Distance from Center of Engine to Front Bearing:, 1.7" (44mm), Distance from Center of Engine to Backplate:, 1.4" (35.6mm), Needle Settings, High Speed:, 2 3/4 turns out from fully closed, Metering Needle (low speed):, flush with ball link body, then 1.5 turns in, Throttle Stop Screw:, 1/2mm open from fully closed, ,
This is the O.S. Max 30VG (P) ES Electric Start, ...RCPlanet
O.S. ENGINES .21VG(P) W/NEW 21F CARB OSM13644
, Displacement:, 0.211 cu in (3.46cc), Bore:, 0.654" (16.6mm), Stroke:, 0.63" (16.0mm), Practical RPM:, 3,000 - 36,000 RPM, Power Output:, 2.0 PS, 1.97 HP/ 30,000 RPM, Weight:, 12.24oz (347g), Distance Between Mounting Holes Same Side:, 0.83" (21mm), Distance Between Mounting Holes Opposite Side:, 1.4" (37mm), Height Bottom of Mounting Tabs/Top of Cylinder Head:, 3.4" (87.4mm), Width of Mounting Tabs:, 1.8" (45mm), Distance from Backplate to Front Bearing:, 2.6" (65.6mm), Distance from Center of Engine to Front Bearing:, 1.7" (44mm), Distance from Center of Engine to Backplate:, 0.85" (21.6mm), Needle Settings, High Speed:, 3 turns out from fully closed, Metering needle (low speed):, flush with ball link body, Throttle Stop Screw:, 1/2 turn out from fully closed, ,
O.S. Engine Max .21 VG-P Pilot Shaft Sport Engine with ...RCPlanet
HPI CRANKSHAFT SG SHAFT F4.6 HPI1493
, Length:, 3.07" (78mm), Diameter At Threaded End:, .27" (7mm), ,
HPI Racing crankshaft is constructed of machined steel with pilot ...RCPlanet
HPI CRANKSHAFT NITRO STAR K4.6 HPI15222
, ,
HPI Racing crankshaft is constructed of machined steel with pilot ...RCPlanet
HPI NITRO STAR F4.6 PULLSTART HPI1495
, ,
HPI Racing Nitro Star has composite construction slide valve, 7.5mm ...RCPlanet
ASSOCIATED LRP Z.28R SPEC 3 ENGINE W/PULL ASCLRP32802
, ,
Associated LRP Z.28R Spec 3 Engine with Pull-Starter, glow plug, ...HiModel
SK 130 AR ACRO ENGINE W/MUFFLER
| Prop shaft diameter | 9.45mm/ 0.37 inch |
| Suitable Prop | 16x 6 / 17x 6 |
| Distance between mounting holes on same side | 0.98" (25mm) |
| Distance between mounting holes on opposite side | 2.3" (58.4mm) |
| Height from bottom of crankcase to top of cylinder head | 4.6" (116.8mm) |
| Height from center of crankcase to top of cylinder head | 3.5" (89mm) |
| Width at mounting flanges | 2.75" (69.85mm) |
| Width at crankcase | 1.8" (45.72mm) |
, , , , , , Specifications:, , , , , , , , , , , weight：730g / 25.75oz (without muffler); 980g/ 34.57oz（with muffler）, MOUNTING DIMENSIONS:, , ,
Features: The SK line of engines is produced in our ...HobbyKing
EME GAS ENGINE AUTO START KIT (50-60CC)
Please note:, , you will need to remove your propeller hub and shaft and install the gear with the one way bearing, you need to be comfortable taking an engine apart as no instructions are included., Compatible with the following engines:, EME55, EME60, DL50, DLE55, DLA56, SE55 plus similar engines (Note that the DLE55RA requires drilling one new mounting hole)., Voltage:, Suits Engines:, Weight:,
A very robust and strong auto start kit for 50-60cc ...HobbyKing
ROTORSTAR APACHE .56 HYPER RINGED TWO STROKE COMPETITION HELI ENGINE
Displacement:, RPM (Max Power):, Practical RPM:, Bore:, Stroke:, Sleeve:, Bearings:, Crankshaft:, Carburetor:, Exhaust:, Weight:, Fuel:,
The RotorStar .56 Hyper helicopter engine is a precision made ...HobbyKing
O.S GT15HZ GAS HELICOPTER ENGINE W/POWERBOOST PIPE
For power, a 25:1 fuel/oil mixture, which is very clean running compared to messy nitro fuel. Fuel for this engine is recommended to use 87 octane and a quality 2-stroke oil, mixed at 25 parts fuel, to 1 part oil., 25:1,
In 1936, Shigeo Ogawa set up his original machine-shop, making ...