ngHobbies
TWINSTAR FPV PAN/TILT POD KIT
Comes with a mounting plate that will fit many popular FPV cameras including: KX131, KX171, KX191, IF Cam, SN777, SN555 and others. Additional back plates may be purchased here to fit IF OSD Cam, DPC OSD Cam, DX201, Note:, careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit includes:, Laser cut components for the main pod, You'll need:, Double sided servo tape to apply TX, camera, and tilt servo., Documentation:, Instructions to build the pan and tilt:, Click here, Instructions to build the Twinstar Pod:, Coming soon,
a Twinstar FPV pod that uses a custom mechanism allowing ...ngHobbies
NANO CMOS CAMERA (PAL)
| Sensor type | CMOS 4.75mm x 3.55mm |
| Resolution | 786x576 (PAL) |
| Signal processing | DSP |
| Lines | 520TVL |
| Sensitiivity | 0.008Lux/F1.2 |
| Lens included | 0.5mm pinhole/62 degrees |
| S/N Ratio | 48db |
| Video out signal | Standard 1VPP/75ohm |
| Dimensions | 9.5mm x 9.5mm x 12mm |
| Weight | 1gr |
| Power | 3.3V-6V |
| White | Video Out |
| Red | 3.3-6V in |
| Black | Ground |
Specifications:, Scanning type: 2:1 Interlaced, Connection diagram:, Manual:, none,
This is the smallest FPV camera on the market today. ...ngHobbies
OPTICAL RPM SENSOR FOR ELOGGER V3 & V2
Measures your RPM without need for installing magnets. Note: This version is for the eLogger V3 and the V2, which we have been selling since early 2006. The eLogger V2 has the large white letters "V2" (or "U2") on the bottom of the circuit board, near the RPM/Temp pins., Manuals:, eLogger Manual,
Click here for instruction manual. If you are not sure ...ngHobbies
500MW LM 2.4GHZ TRANSMITTER
Please note: This product will not be sold/shipped to USA customers. Your order of the product will be cancelled and your payment refunded., Features:, Frequency Band:, 2400MHz, Number of Channels:, 8, Audio Sub-carrier:, 6.5MHz, Transmission Range:, 200-500 Meter, Power Consumption:, 450mA, Output Power:, 500mW, Operation Voltage:, 5-5.5V, Power Supply:, 5V/500mA, Antenna Connector:, SMA Connector, Weight:, 10 g, Dimensions:, 24 x 28 x 7 mm, Documentation:, , Warranty:, 6 months, Note:, The use and operation of this product in most states will require a HAM or Amateur radio license., Important note for Canada customers:, Please note, channels 4,5,6,7 and 8 of this transmitter are outside of the allowed frequency spectrum for Canada. These channels cannot be legally used even if you have a Radio Amateur license. Please make sure that you obey Industry Canada regulations around use of these devices and use them only on channels 1, 2 and 3. New Generation Hobbies cannot be held responsible for using these transmitters on channels which are outside of the legal allowed frequency ranges.,
Highly integrated mini 2.4 GHz transmitter with well known quality ...ngHobbies
LMR-195 SMA MALE TO SMA FEMALE ANTENNA CABLE
Connectors:, 1 x SMA Male,
Constructed of premium LMR-195 Low-Loss 50 ohm RF outdoor coaxial ...ngHobbies
BOB4SG
| http | //www.decadenet.com/ |
Key Features:, Simple hookup; requires just DC, serial data, video I/O, Documentation:, BOB-4 Application Guide, Home page with more application and product information:,
BOB-4 is Decade's fourth-generation low-cost video information overlay module, now ...ngHobbies
AWM651-TX 10MW MODULE
Please note: this product might ship with headers soldered in, depending on how we receive these from the manufacturer.,
The Airwave AWM651 Transmitter module operates at 5V. It is ...ngHobbies
AWM655-TX 100MW MODULE
Please note: this product might ship with headers soldered in, depending on how we receive these from the manufacturer,
The Airwave AWM655 Transmitter module operates at 5V. It is ...ngHobbies
TINYTELEMETRY CABLE
,
Replacement cable for the TinyTelemetry. This cable goes between the ...ngHobbies
EZANTENNATRACKER ANTENNA PAN/TILT
Documentation:, Instructions to build the pan and tilt:, Click here,
Antenna pan/tilt assembly kit designed to work with the ImmersionRC ...