HiModel
KYOSHO GXR-28 ENGINE W/RECOIL STARTER FOR CARS
Kyosho GXR28 engine. It has 4.6cc ..." />
| Shaft length | 30mm |
| Displacement | 4.6cc |
| Weight | 410g |
| Mounting spacing (approx.) | 21mm same side, 39mm opposite side |
| Mounting hole diameter | 3mm |
| ① Needle value | 2 and 1/2 turns unscrewed from closed position. |
| (Caution | after each tank, allow the engine to cool off naturally!) |
, , , , , , Specifications:, , , , , , , , , , , * Note: As this engine is produced as OEM from ASP for Koyosho, the outer box you receive may with ASP marks, this is not a mistake., ● Engine starting & break-in, Adjust the needle valve and air/fuel mixture adjustment screw to their standard position as follows:, ② Air/fuel mixture adjustment: Gently screw in the idle mixture screw to closed position (clockwise); 2 and 1/2 turns unscrewed from closed position (counter clockwise), Adjustments ① ~ ② may slightly vary according to the type of glow plug and glow fuel., Proceed as follows when starting and breaking the engine in:, 1. Make sure the needle valve is unscrewed 2-1/2 turns from closed position., 2. Fill fuel into the tank. Move the throttle lever to the high position, prime the engine (push the choke button 2 to 3 times or put 2 to 3 drops of fuel directly into the carburetor) and move the throttle lever back to the slow throttle position., 3. Attach the booster cord or one-touch glow plug heater to the engine in order to electrify the glow plug., 4. Quickly pull the recoil starter rope (starter knob) several times. Only pull out 20 to 30cm of cord., (Caution: be careful not to pull out more than 50cm of cord because you may tear it and the spring inside the recoil starter!), 5. Once the engine is started, wait 5 to 10 seconds before detaching the booster cord or one-touch glow plug heater., 6. Run the engine another 2 to 3 tanks and make sure you do not apply full throttle. Also afterwards, do not increase RPM abruptly! Tighten the needle valve by 1/8 turns and continue to run the engine, handling it gently., 7. During the break-in, adjust the idle rpm with the throttle valve adjustment screw.. If rotating it clockwise (right), idle rpm increase. Idle rpm are halfwa,
Features: This is the Kyosho GXR28 engine. It has 4.6cc ...HiModel
KYOSHO GXR-15 ENGINE W/RECOIL STARTER FOR CARS
| Displacement | 19.96cc |
| RPM range | 3,000-19,000(r.p.m) |
| Output | 0.58/16,000(kw/r.p.m) |
| Weight | 227g |
| ① Needle value | 2 and 1/2 turns unscrewed from closed position. |
| (Caution | after each tank, allow the engine to cool off naturally!) |
, , , , , , Specifications:, , , , , , , , , , , * Note: As this engine is produced as OEM from ASP for Koyosho, the outer box you receive may with ASP marks, this is not a mistake., ● Engine starting & break-in, Adjust the needle valve and air/fuel mixture adjustment screw to their standard position as follows:, ② Air/fuel mixture adjustment: Gently screw in the idle mixture screw to closed position (clockwise); 2 and 1/2 turns unscrewed from closed position (counter clockwise), Adjustments ① ~ ② may slightly vary according to the type of glow plug and glow fuel., Proceed as follows when starting and breaking the engine in:, 1. Make sure the needle valve is unscrewed 2-1/2 turns from closed position., 2. Fill fuel into the tank. Move the throttle lever to the high position, prime the engine (push the choke button 2 to 3 times or put 2 to 3 drops of fuel directly into the carburetor) and move the throttle lever back to the slow throttle position., 3. Attach the booster cord or one-touch glow plug heater to the engine in order to electrify the glow plug., 4. Quickly pull the recoil starter rope (starter knob) several times. Only pull out 20 to 30cm of cord., (Caution: be careful not to pull out more than 50cm of cord because you may tear it and the spring inside the recoil starter!), 5. Once the engine is started, wait 5 to 10 seconds before detaching the booster cord or one-touch glow plug heater., 6. Run the engine another 2 to 3 tanks and make sure you do not apply full throttle. Also afterwards, do not increase RPM abruptly! Tighten the needle valve by 1/8 turns and continue to run the engine, handling it gently., 7. During the break-in, adjust the idle rpm with the throttle valve adjustment screw.. If rotating it clockwise (right), idle rpm increase. Idle rpm are halfway between rpm when the clutch engages and rpm when,
Includes/Requires: Includes:1 x engine 1 x manual (multi-language, including English) ...8 Reviews
HiModel
KYOSHO GXR-18 ENGINE W/RECOIL STARTER FOR CARS
| Shaft length | 14mm |
| ① Needle value | 2 and 1/2 turns unscrewed from closed position. |
| (Caution | after each tank, allow the engine to cool off naturally!) |
, , , , , , Specifications:, , , , , , , , , , , * Note: As this engine is produced as OEM from ASP for Koyosho, the outer box you receive may with ASP marks, this is not a mistake., ● Engine starting & break-in, Adjust the needle valve and air/fuel mixture adjustment screw to their standard position as follows:, ② Air/fuel mixture adjustment: Gently screw in the idle mixture screw to closed position (clockwise); 2 and 1/2 turns unscrewed from closed position (counter clockwise), Adjustments ① ~ ② may slightly vary according to the type of glow plug and glow fuel., Proceed as follows when starting and breaking the engine in:, 1. Make sure the needle valve is unscrewed 2-1/2 turns from closed position., 2. Fill fuel into the tank. Move the throttle lever to the high position, prime the engine (push the choke button 2 to 3 times or put 2 to 3 drops of fuel directly into the carburetor) and move the throttle lever back to the slow throttle position., 3. Attach the booster cord or one-touch glow plug heater to the engine in order to electrify the glow plug., 4. Quickly pull the recoil starter rope (starter knob) several times. Only pull out 20 to 30cm of cord., (Caution: be careful not to pull out more than 50cm of cord because you may tear it and the spring inside the recoil starter!), 5. Once the engine is started, wait 5 to 10 seconds before detaching the booster cord or one-touch glow plug heater., 6. Run the engine another 2 to 3 tanks and make sure you do not apply full throttle. Also afterwards, do not increase RPM abruptly! Tighten the needle valve by 1/8 turns and continue to run the engine, handling it gently., 7. During the break-in, adjust the idle rpm with the throttle valve adjustment screw.. If rotating it clockwise (right), idle rpm increase. Idle rpm are halfway between rpm when the clutch engages and rpm when the engine stalls. Set idle rpm towards the lower end if possible., 8. No,
Includes/Requires: Includes:1 x engine (No English manual supplied with this ...1 Reviews
HiModel
CUPID II ELECTRIC HELICOPTER RTF(HM-1003)
| Model No. | HM-1003 |
| Model Name | Cupid II |
| Main rotor diameter | 530mm |
| Fuselage length | 500mm |
| Weight | 280-300g |
| Radio Controller | 4 Channel FM |
| Frequency | 35Mhz (only 35Mhz available currently) |
| Servo | 2*9g |
, , , , , , Specifications:, , , , , , , , , , , Battery;8.4V Ni-Mh, , ,
Features: The fuselage widely using carbon fiber and nylon, making ...