DPCAV
STV5730A OSD (ON-SCREEN DISPLAY) IC
STV5730A Data Sheet:, Click Me!, STV5730A Tech Notes:, Click Me!,
The STV5730A OSD (on-screen display) IC has been out of ...DPCAV
5VDC 5A VOLTAGE REGULATOR (BEC), SWITCH-MODE TYPE
| White | Not installed (N/A) |
| Red | +5VDC Output |
| Black | Ground |
| Specifications | Input |
| Output | 5VDC, 5A maximum |
| Technology | Switch-Mode Regulator |
| Size | 1.5 x 0.8 x 0.5 inch (38x21x13mm) |
| Weight | 9 grams |
| Origin | Made in China by AEO Tech |
The DC input has 2-inch bare leads (Red wire = BAT+). The 5-inch long output cable has a 3-pin servo style connector, wired as follows:, ,
This step-down Voltage Regulator accepts 6-23 VDC on its input ...DPCAV
GUARDIAN 2D/3D INERTIAL STABILIZER (STANDALONE MODEL)
| Instruction Manual | Click Me! |
| PC Software | Click Me! |
Q: Why do I need the Guardian?, The Guardian helps both beginner and expert pilots fly with confidence, and provides two key modes of operation: In 2D flight mode, the Guardian provides much smoother flight and wing leveling stabilization for your model, which makes it a lot easier to adjust and fly your plane. The Guardian "remembers" level flight for your model and returns it to level flight when needed, as well as providing precise "fly by wire" control., The Guardian has two submodes for 3D flying: In 3D Heading Lock submode, simply center your sticks to have the Guardian lock onto your present attitude (pitch, roll, and heading), which can make it easier to perform stunts like prop hanging, inverted flight, knife edges, low speed harriers, etc. In 3D Gyro submode, the Guardian uses its built-in 3 axis gyro to increase your model’s stability, while leaving you in full control. In this mode the Guardian greatly reduces the effects of gusts, turbulence, motor torque and other factors, and can expand the maneuverability of your model in a variety of conditions., Q: I Fly FPV. Is the Guardian for me?, Q: Will the Guardian work with my model?, Q: How do I install the Guardian?, Q: How do I configure the Guardian?, Q: How does the Guardian work?, Q: What sets the Guardian apart from other Stabilization systems out there?, *Note: Using the PC software will require a common Micro-USB cable. Most likely you already have one of these, but it not then they are available from your local electronic/computer store.,
Based on Eagle Tree's proven inertial stabilization technology, the Guardian ...DPCAV
DIGITAL OSCILLOSCOPE, 2-CHANNEL / 10MHZ (PORTABLE)
| Analog Bandwidth | 0 - 10MHz |
| Sensitivity | 10mV/Div - 2V/Div |
| Resolution | 8-bit |
| Input Impedance | 1M ohm |
| Maximum Input voltage | 50Vpk (for 1X probe) and 400Vpk (for 10X probe) |
| Coupling | DC, AC, GND |
| Max Real-time Sampling Rate | 50MSps |
| Timebase | 0.2us/Div - 10 minutes/div |
| Record Length | 500 - 8000 points (each channel) |
| Run/Hold Modes | one button switchable |
| Trigger Modes | Auto, Normal, Single |
| Trigger Types | Rising/falling edge |
| Trigger Sources | Ch 1 or Ch 2 |
| Trigger Position | 0 - 100% of capture buffer |
| Supply Current | 300mA @ 3.7V(LCD backlight ON, typical). |
| Dimension | 140mm X 70mm X 30mm |
| Weight | 190 gram (including battery) |
| Documents, firmware, and tools | Users Manual |
Portable 2-Channel 10MHz Digital Oscilloscope:, This portable scope offers a lot of features at an affordable price. It has 2-channels with 10MHz analog bandwidth (50msps) and it includes a rechargeable battery pack. Two switchable 10X scope probes are provided too!, The DSO-094 has useful features that are not commonly found in other low cost oscilloscopes. For example: It can be placed in "Persistent Display" mode that keeps waveforms on screen until you erase them; This is very useful when combined with NORMAL trigger mode to capture and compare multiple waveforms that meet your trigger conditions., Features:, , Specifications:, , Number of Channels: 2,
This is a FACTORY ASSEMBLED scope; It is not a ...