ngHobbies
GOPRO CAMERA MOUNT FOR MK HEXA/OKTO
This GoPro Hero camera mount comes installed underneath, in the center of gravity of the Mikrokpter. It is also possible to install further to the front, so the wide angle of the GoPro will catch only minimal parts from the landing gear or the front outrigger. Installing it in such position we have achieved two important goals:, All motors work equally since nothing is off balance, Features:, Low cost, minimal parts. Pieces are CNC cut from 1.7mm G10/FR4, Package contains:, All necessary plates, screws, nuts and washers, Note:, Assembly required., Cables:, Do not forget to pick up a GoPro FPV cable from here:, GoPro Camera Cables, Demo Videos:, Outdoor testing - click here, Note:, This kit comes with a mounting plate which either replaces of can be sandwitched under the battery holding plate on Hexa and Optokopters. Additional mountig plates for Quads will be available soon., Assembly documentation:, Click here to open or download (2Mb),
New Generation Hobbies is proud to present this low cost ...ngHobbies
GOPRO CAMERA MOUNT FOR MK HEXA/OKTO NO SERVOS
This GoPro Hero camera mount comes installed underneath, in the center of gravity of the Mikrokpter. It is also possible to install further to the front, so the wide angle of the GoPro will catch only minimal parts from the landing gear or the front outrigger. Installing it in such position we have achieved two important goals:, All motors work equally since nothing is off balance, Features:, Low cost, minimal parts. Pieces are CNC cut from 1.7mm G10/FR4, Package contains:, All necessary plates, screws, nuts and washers, Note:, Assembly required., Cables:, Do not forget to pick up a GoPro FPV cable from here:, GoPro Camera Cables, This GoPro Hero camera mount comes installed underneath, in the center of gravity of the Mikrokpter. It is also possible to install further to the front, so the wide angle of the GoPro will catch only minimal parts from the landing gear or the front outrigger. Installing it in such position we have achieved two important goals:, All motors work equally since nothing is off balance, Features:, Low cost, minimal parts. Pieces are CNC cut from 1.7mm G10/FR4, Package contains:, All necessary plates, screws, nuts and washers, Note:, Assembly required., Cables:, Do not forget to pick up a GoPro FPV cable from here:, GoPro Camera Cables, Demo Videos:, Outdoor testing - click here, Note:, This kit comes with a mounting plate which either replaces of can be sandwitched under the battery holding plate on Hexa and Optokopters. Additional mountig plates for Quads will be available soon., Assembly documentation:, Click here to open or download (2Mb),
New Generation Hobbies is proud to present this low cost ...ngHobbies
FPV TRAY FOR THE GOPRO CAMERA MOUNT
GoPro camera ..." />
The package contains:, 1 x FPV Tray, Cables:, Do not forget to pick up a GoPro FPV cable from here:, GoPro Camera Cables,
This is an FPV tray expansion for the GoPro camera ...HiModel
UNIVERSAL FIBERGLASS DUAL-SHAFT DAMPING AERIAL TILT T8 (SUIT FOR CAMERA GOPRO)
Gopro etc." />
| Material | Fiberglass + metal |
| Mounting tube diameter | 8mm (suit for 8mm tube) |
| Weight | 60g (excluding servo) |
| Moving direction | 2 axis |
| Servo requirement (not included) | 1 x standard size servo(like Futaba 3001, 3003 etc), 1 x 9g mini servo |
, , , , , , Specifications:, , , , , , , , , , , Universal Dual-shaft Damping Aerial Tilt T8 (suit for Camera Gopro), * Not assembled, come in loose parts), , ,
Features: Suit for car cameras like Gopro etc.HiModel
VOYAGER UNIVERSAL FIBERGLASS DUAL SHOCK ABSORBING AERIAL GIMBLE (SUIT FOR GOPRO ETC.)
Gopro etc. Dual shock ..." />
| Material | Fiberglass |
| Mounting tube diameter | 8mm (suit for 8mm tube) |
| Weight | 166g (excluding servo) |
| Servo requirement (not included) | 1 x standard size servo(like Futaba 3001, 3003 etc), 1 x 9g mini servo |
, , , , , , Specifications:, , , , , , , , , , , VOYAGER Universal Fiberglass Dual Shock Absorbing Aerial Gimble (suit for Gopro etc.), * Not assembled, come in loose parts), * Servos are NOT included., , ,
Features: Suit for car cameras like Gopro etc. Dual shock ...HiModel
FLYCAT 4-AXIAL DIY FRAME W/GOPRO GIMBAL (CAMERA MOUNT)
| Motor spacing(distance between motor axles, cross side) | 480mm |
| Mode | 4-axial |
| Brushless motor | HL 4225-610. |
| Battery | 3000-4000mAh 4S |
| Suggested prop | 10x4.5 3-blade |
, , , , , , Specifications:, , , , , , , , , , , FLYCAT 4-axial/Xcopter DIY Frame W/Gopro Gimbal (Camera Mount), * Electronics and propellers are not included, to be purchased separately., --------------------------------------------------------------------------------------------, Suggested setting (not included):, , ,
Features: This DIY frame can adopt most popular flight control ...HiModel
SHOCK ABSORBING & DAMPING AERIAL GIMBAL FOR GOPRO CAMERA
Gopro etc. Shock absorbing ..." />
| Material | Fiberglass |
| Weight | 60g (excluding servo) |
| Servo requirement (not included) | 2 x 9g mini servo |
, , , , , , Specifications:, , , , , , , , , , , Shock Absorbing & Damping Aerial Gimbal for Gopro Camera, * Not assembled, come in loose parts), * Servos are NOT included., , ,
Features: Suit for car cameras like Gopro etc. Shock absorbing ...GetFPV
LAYERLENS GOPRO LENS PROTECTION (FOR GOPRO 1 & 2)
GoPro camera is ..." />
NOTE: This version of LayerLens is not compatible with the GoPro Hero 3. A new LayerLens for the Hero 3 will be released soon., For this reason, FPV Manuals has developed LayerLens. LayerLens brings the most important part of the original GoPro case back: the protective lens; without adding much weight or size. LayerLens weighs only 11g — about 10% of the weight of the GoPro case. LayerLens is a precision laser cut frame that holds the protective glass lens found in the GoPro's case. LayerLens is pushed onto the GoPro’s built in lens. It sits tightly in place and is secured by an included velcro band. In case of a crash that scratches LayerLens’ glass lens, you can easily swap out the scratched protective lens and replace it with one of the lenses that are readily available by GoPro as part of their “Lens Replacement Kit” (which includes 2 lenses for $14 to $20 USD).,
Details The case that comes with the GoPro camera is ...BevRC
TAROT T2D GOPRO HERO3 TWO-AXIS BRUSHLESS GIMBAL/WITH GYRO
| 7, support Receiver | conventional receiver, S-BUS receiver, DSM2/DSMJ/DSMX receiver |
| 8, support for remote devices | PPM/PCM/2.4G |
| 9, the working voltage | DC 7.4V ~ 14.8V (Recommended 12V, three lithium battery) |
| 10, working current | 200mA-500mA (power supply voltage and the motor related) |
| 11, the working environment temperature | -15 ℃ ~ 65 ℃ |
| 12, the processor | Dual 32-bit high-speed ARM core processor |
| 13, the sensor | Three rotor MEMS gyroscope rotor MEMS accelerometers and the three |
| 14, the maximum angular rate | 2000°/ sec |
| 15, the maximum acceleration | 16g |
| 16, the control frequency | 2000Hz |
| 17, the motor drive frequency | 20KHz (no noise smoothing driven) |
| 18, the control accuracy | 0.1° |
| 19, the control angle range | -45 °~ 45 °(roll), -135°~ 90°(tilt) |
| 20, pose solver algorithms | PTZ dedicated brushless motor decoupled EKF algorithm |
| 21, for shooting equipment | GOPRO Hero3 |
| Weight | 195g |
Gopro two-axis brushless PTZ English software description and download link:, , Product Features:, 1, support GOPRO Hero3 video auxiliary output, Related Part Number:, Head hanging hook TL68A01, Specifications:, GOPRO brushless pan rack assembly TL68A08 x1,
Download the manual here. T-2D PTZ is TAROT company for ...BevRC
MASTOR-G BRUSHLESS GIMBALS FOR GOPRO(FREE SHIPPING IN EXPEDITED WAY)
| Free Download | firmware update.zip |
| Weight | 232g without camera |
| roll | 0.07 degrees; pitch |
| 12-hours angle drift | 0.12-1.5 degrees |
| Suitable payload | 120g-400g |
| Suitable flying wind Speed | < 38km/h |
Free Download:, Mastor-G quick start manual 2013-5-18.pdf, Free Download:, GoPro-G Assistant Software.zip, Leave us a note in your order such as:, 1: what lipo you plan to use, 3 cell or 4 cell lipo, 2: what camera you plan to use, gopro hero1/2 or hero3, All the gimbals shipped after 18th, May will be registered and with the sticker marked the SN number and register code, as below pic shows, pre adjusted with 3s lipo and naked gopro:, , ry please send email to:, support@bevrc.zendesk.com, Specs:, Based on STM32 32-bits high-speed MCU(tens of times faster than other open-source solutions), Size:, 10.7(12.5)*11*12cm, Roll angle limit:, > 360 degrees, Pitch angle limit:, >180 degrees, can be controlled by any p, : roll: 178 degrees/s; pitch: 182 degrees/s, Control accuracy:, Recommend camera:, gopro hero1,hero2, hero3, or similar cameras, Power:, 2-4 cell lipo, 3-cell recommend, can be powered as high as 6-cell(the high voltage input need to be reduce the power output parameters in the configuration tool.), COG adjustment range: X: 28mm Y:12mm Z:36mm,
We will pre-adjust it well for you to guarantee you ...HobbyKing
GOPRO HERO3 GLASS FIBER CAMERA MOUNT
| Application | GoPRO HERO3 |
| Interior Dimensions (mm) | 60Lx25Wx45H |
| Weight | 55g |
Specs:,
This camera mount is contructed from strong yet lightweight glass ...5 Reviews
HobbyKing
X-CAM X100B 2-AXIS BRUSHLESS CAMERA GIMBAL FOR GOPRO (PLUG AND PLAY)
| Motor Travel Limit | +/- 90° |
| Sensor Resolution | 0.015 |
| Twin Rail Mount Width | 59~60mm |
| Weight | 230g |
*Compatibility:, This gimbal is compatible with the GoPRO Hero 1~3 and other similar sized cameras., Features:, • Designed for use with the GoPRO Hero 1~3 and other similar sized sports cameras, Specs:, Input Voltage:, 12V (recommended to use a 12V BEC), *Note:, The X-Cam Brushless Gimbal PC Assistant software, USB link drivers and User Manual can be downloaded from the "Files" tab below.,
This is the X-Cam X100B 2-axis brushless camera gimbal for ...5 Reviews
SDSHobby
CNC ALUMINIUM ALLOY BRUSHLESS GOPRO CAMERA GIMBAL FOR FPV AERIAL PHOTOGRAPHY/ GOPRO3
Gopro ..." />
| 4. Support Receiver | general receiver, S-BUS receiver, DSM2/ DSMJ/ DSMX receiver. |
| 5. Remote control | PPM/ PCM/ 2.4G |
| 6. Operating Voltage | DC 7.4V~14.8V (recommended 12V, 3-cell lithium battery) |
| 7. Operating Current | 200mA-1000mA (Related to supply voltage and motor power) |
| 8. Operating Temperature | -18°C~70°C |
| 9. Control frequency | 2000Hz |
| 10. Motor driving frequency | 20 KHz (noiseless smooth drive) |
| 12. Controlled angle range | -45~45degree (roll), -60~60degree (pitch) |
| 13. Suitable film device | GOPRO Hero3, GOPRO Hero3+ |
Product Description:, Features:, 1. Support video, 11. Control precision:, 0.1 degree, 17. Whole weight:, 160g, Package Details:, *Attention:, GOPRO3 camera,
GOPRP3 ( free debugging ) gimbal is designed for Gopro ...SDSHobby
2-AXIS BRUSHLESS GIMBAL/CAMERA MOUNT WITH ALEXMOS CONTROLLER & MOTOR & SENSOR FOR GOPRO 3 FPV DJI PHANTOM BLACK & SILVER
| - Weight | 230/300g (without / with Gopro hero 3) |
| - Available Colors | Black and Silver |
:, -, Package included:, - 1 x Aluminum gimbal installed 2 motors, Notice:, The Gopro camera and,
Features - Debugged - Simple structure and light weight, CNC ...SDSHobby
3-AXIS CNC BRUSHLESS GIMBAL/CAMERA MOUNT WITH ALEXMOS CONTROLLER FOR GOPRO 3/3+ FPV DJI PHANTOM1/2
| - Voltage | 12V (3S lipo battery) |
| - Current | 150mA |
| - Height | 8.8cm |
| - Weight | 200g/274g(without/with Gopro 3+) |
| - Color | Black |
Features:, - Assembled and debugged, ready to fly, Specification:, Package Included:, - 3-Axis brushless Gopro 3/3+ Gimbal with Motor & Gimbal driver (Assembled),
- CNC Aluminum alloy processing, black anodizing - Compact structure, ...