RCPlanet
ASSOCIATED CRANKSHAFT .15 SG ASC29006
, Length:, 69.5mm (2.74"), Crankshaft threading:, 1/4-28, Pilot shaft diameter:, 5mm (.20"), Crankshaft diameter:, 7mm (.28") (flywheel position), ,
Associated crankshaft fits into the crankcase and the clutch nut, ...HobbyKing
TURNIGY MINI POWER PANEL - 12V WITH AUTO GLOW DRIVER
Size | 85mm x 46mm x 18mm |
Weight | 65g |
5 Reviews
HobbyKing
TURNIGY POWER PANEL MKII WITH AMP METER & REMOTE GLOW CHARGER
Size | 152mm x 92mm x 22mm |
Weight | 155g |
5 Reviews
RCPlanet
ASSOCIATED AE 8.0 ENGINE ASC25480
Three turns counter clockwise from closed Low Speed Mixture | Five and one half turns counterclockwise from closed |
, Displacement:, .50 cu in (8.0cc), High Speed Mixture:, Idle Speed:, Turn screw until throttle opening inside throttle valve is .050" (1.3mm), Weight:, 14.5oz (410g), Distance Between Mounting Hole Centers Same Side:, 0.67" (17mm) Distance Between Mounting Hole Centers, Opposite Side:, 1.6" (42mm), Height from Mounting Tab Bottom to Top of Cylinder Head:, 3.9" (100mm), Height from Crankcase Bottom to Top of Cylinder Head:, 4.6" (116mm), Length from Backplate to Front Bearing:, 3.3" (83mm), Length from Backplate to Crankshaft End:, 0.63" (116mm), Width at Mounting Tabs:, 2.0" (50mm), Cylinder Head Diameter:, 2.2" (56mm), ,
Associated Nitro engine is a direct replacement engine for the ...RCPlanet
TRAXXAS ENGINE BIG BLOCK INSTALLATION KIT REVO TRA5360X
, ,
Traxxas big block conversion kit components required to install a ...RCPlanet
TRAXXAS TRX 2.5R RACING ENGINE WITH RECOIL PULL START TRA5207R
, Displacement:, 0.15 cu in (2.49cc), Crankshaft Thread:, 5mm (.197"), On-Center Mounting Holes, Front to Rear:, 11mm (.433"), On-Center Mounting Holes, Side to Side:, 31.4mm (1.24"), Back of engine (recoil) to front of drive washer:, 73.2mm (2.88"), Height:, 97.3mm (3.83"), Inner Exhaust Port Diameter:, 9.9mm (.392"), Outer Exhaust Port Diameter:, 13.0mm (.512"), ,
Traxxas racing engine with recoil and pull start This is ...RCPlanet
THUNDER TIGER PRO .39H RINGED TTR9604
, Displacement:, 0.394 cu in (6.45cc), Bore:, 0.850" (21.6mm), Stroke:, 0.693" (17.6mm), Output:, 1.35 hp @ 16,000 RPM, RPM Range:, 2,000 - 17,000, Weight w/o Muffler:, 10.23oz (290g), ,
Thunder Tiger Pro-39H delivers smooth power for sport and 3D ...RCPlanet
THUNDER TIGER HI-FLOW 3D PIPE RL-53 TTR9722
, Length:, 10.4" (266mm), Diameter:, Body 1.7" (43mm), Diameter:, Tip .47" (12mm), ,
This is the Thunder Tiger Redline HI-FLOW 3D Pipe #9722 ...RCPlanet
TRAXXAS CRANKSHAFT IPS WITH OUT STARTER FOR THE TRX 3.3 TRA5288R
, ,
Traxxas crankshaft with IPS is constructed of steel. IPS (Integrated ...RCPlanet
O.S. ENGINES CRANKSHAFT 12XZ SPEED OSM21652000
, ,
O.S. Engines crankshaft is constructed of steel. Pilot shaft design. ...RCPlanet
OFNA PICCO .26 MAX JL RED-DOT T-MAXX/REVO OFN51225
, ,
This is the Ofna/Picco .26 (4.27cc) Max JL Red Dot ...RCPlanet
OFNA .28 PICCO JL TEAM TURBO OFN51234
, RPM:, 37,000, Claimed Horsepower:, 3.4, Ports:, 7, Stroke:, 0.69" (17.6mm), Bore:, 0.72" (18.35mm), Weight:, 12.3oz (350g), Distance Between Mounting Holes Same Side:, 0.83" (21mm), Distance Between Mounting Holes Opposite Side:, 1.5" (38mm), Height from Bottom of Crankcase to Top of Cylinder Head:, 4.4" (111mm), Height from Bottom of Mounting Tab/Top of Cylinder Head:, 3.8" (96mm), Height/Exhaust Port Center to Crankcase Bottom:, 1.8" (47mm), Width at Mounting Tabs:, 1.7" (44.2mm), Length from Backplate to End of Crankshaft:, 3.7" (94mm), Length from Backplate to Front Bearing:, 2.5" (64.5mm), Note:, Carburetor is factory adjusted. Only very small adjustments should be made. Ofna does not state specific number of turns for carb needles., ,
Ofna Picco .28 JL Team Turbo Engine is designed for ...RCPlanet
OFNA .28 OFF-ROAD TRUGGY PS FORCE OFN52217
, Displacement:, .28 cu in (4.58 cc), Bore:, 18.68mm, Stroke:, 16mm, Output:, 2.9 PS @ 32,000RPM, Practical RPM Range:, 2,500 - 32,000, Weight:, 16.7oz (475g), Distance between mounting hole centers/same side:, 0.83" (21mm), Distance between mounting hole centers/opposite side:, 1.4" (37mm), Height/bottom of mounting tab to top of cylinder head:, 4" (102mm), Height/bottom of crankcase to top of cylinder head:, 4.5" (115mm), Width at mounting tabs:, 1.8" (45.8mm), Length from pull starter to front bearing:, 3.3" (84.2mm), Length from pull starter to end of crankshaft:, 4.5" (114mm), Carb needle settings, Main Needle Valve:, 3-3-1/2 turns form closed, Low Speed Needle:, Located in the center side of carb, set flush with ball end, Barrel Stop Screw:, Set for 1/16" inch gap, ,
Ofna engine is ABC cylinder liner construction "A"luminum piston with ...RCPlanet
OFNA CLUTCH NUT SG SHAFT OFN10098
, ,
FEATURES: Steel clutch nut for Ofna .21 engines INCLUDES: One ...