GetFPV
CAMERA TO EZOSD CABLE
Custom-made cable from the EzOSD to cameras. Works with TBS59 and 69. Great spare part or work-saver. Length: 14",
DetailsGetFPV
FUTABA/HITEC ADAPTER FOR AEROSIM RC FLIGHT SIMULATOR
,
Details Futaba/Hitec DIN6 trainer adapter used to connect to the ...GetFPV
FPVMANUALS LIPO VELCRO STRAP (3PCS)
,
Details The fpvmanuals branded Velcro Lipo Strap is made by ...GetFPV
90 DEGREE MALE TO FEMALE SMA CONNECTOR (1 PCS)
,
Details SMA Female to SMA Male right angle (90 degree) ...GetFPV
TEAM BLACKSHEEP ZII CAMERA CASE
The new GoPro / Flight Cam mount for the ZII Zephyr Wing that was developed by Team Black Sheep. This new case is a sturdy plywood construction that protects your flight cam and GoPro. The kit comes with:, Plywood GoPro Camera & FPV mount,
Details Spare plywood front plate Velcro strap This product does ...GetFPV
DJI NAZA M MULTI-ROTOR STABILIZATION CONTROLLER AND GPS/COMPASS
Naza-M offers three types of control modes: GPS Atti. Mode(with GPS module), Atti. Mode, Manual Mode. Switch among the three modes to adjust to different flight environments. Naza-M can adjust automatically and intelligent switch between GPS Atti.mode and Atti. Mode to ensure the safety and security of the flight., Immediately Mode: By using this mode once the motors start and throttle stick has exceeded 10%, motors will stop immediately when throttle stick is back under 10% again. In this case, if you push the throttle stick over 10% within 5 seconds of the motors stopping, motors will re-start .If you don’t push throttle stick within three seconds of the motors starting, the motors will stop automatically., Intelligent Mode: In Manual, only executing CSC will stop motors. In Atti Mode. any one of following four cases will stop motors:, a) You don’t push throttle stick after motors start in three seconds;,
Details NAZA simplifies installation on your multi-rotor; saving space and ...GetFPV
DJI NAZA M GPS/COMPASS
,
Details High quality GPS for your multi-rotor. Uses Accurate GPS ...GetFPV
QAV500 BRUSHLESS GIMBAL UPGRADE (PRE-ORDER)
| 10" Props that generate a maximum of lift. Recommended props | APC 10x4.7 |
| Motors | We recommend the |
| ESCs | We recommend the |
Gimbal Control Board:, We recommend the AlexMos board., Props:, Lipo:, A 5000mah 4s Lipo that is no wider than 51mm and no higher than 35mm (or it will not fit in the lipo compartment). We recommend HobbyKing Nano-Tech Lipos., GoPro protection:, The QAV540G gimbal that is part of this upgrade requires the GoPro to be placed into the gimbal without the GoPro case. We recommend you buy a separate, Shipping details:, When placing a pre-order, the entire order you place will be put on hold until the pre-ordered item is in stock and ready to ship. Please make a separate order for any additional items outside of the pre-order if you would like them to ship sooner, otherwise they will ship with your pre-order.,
Details Turn your existing QAV500 quad into an airframe with ...GetFPV
IFLIGHT GIMBAL MOTOR GBM2208-80T
| Weight | 43g |
| Motor Dimensions | 28x22mm |
| Stator Dimensions | 22x8mm |
| Copper wire(OD) | 0.16mm |
| Configuration | 12N14P |
| Resistance | 14.6 ohms |
| Wind type and termination method | Star style |
| Bottom mounting holes | 16 and 19mm center to center |
| Top mounting holes | 12mm center to center |
| Camera range | 100-200grams(GoPro size) |
GetFPV
FEMALE JST BATTERY PIGTAIL 10CM (10PCS/BAG)
,
Details High quality silicon wire provides a higher amp output ...GetFPV
IFLIGHT GIMBAL MOTOR GBM4008-150T
| Weight | 102g |
| Motor Dimensions | 50x17mm |
| Stator Dimensions | 40x8mm |
| Copper wire(OD) | 0.21mm |
| Configuration | 12N14P |
| Resistance | 16.3 ohms |
| Wind type and termination method | Star style |
| Bottom mounting holes | 16 and 19mm center to center |
| Top mounting holes | 12mm center to center |
| Camera range | 400-800grams(Nex6 and Nex7 Size) |
GetFPV
OSD PRO PKG WITH 100A ELOGGER/WIRE LEADS AND GPS
There are lots of OSD choices out there. Here are a few reasons why the OSD Pro may be your best option:, Modularity:, If we come out with a newer version of one of the OSD Pro components, you only need to upgrade that component to have the latest and greatest system, rather than having to replace your entire OSD system when a new one comes along., Easy setup:, The OSD Pro is easy to configure exactly like you want it, with the included software., Stabilization:, with the new Guardian Stabilization Expander, the OSD Pro provides full model stabilization with no additional stabilization equipment to buy., Expandability:, Eagle Tree offers myriad sensors that are fully compatible with the OSD Pro. Since we make these sensors ourselves, you're guaranteed that they will be plug and play, with no soldering, finger pointing, or headaches., Powerful features:, The OSD Pro offers advanced features, such as Voice Alerts, Programmable Alarms, "RADAR" synthetic map, "Return to Home", RSSI and multiple battery voltage displays, built-in Flight Simulator for setup testing,Artifical Horizon display, acoustic variometer, waypoints, full Data Logging with GoogleEarth and graphing with the powerful software., World class support:, Eagle Tree has a full time, dedicated support staff, should you ever have a problem. They offer 24/7 support with their, Easy upgradability:, We are constantly adding new features and enhancements to the firmware. These are just a download away. The OSD Pro's built-in USB connection makes it easy to update firmware with the powerful software. No need to buy a separate USB adapter, build any special cables, or other complex steps for update., Part of a complete FPV system:, The OSD Pro is complimented by our EagleEyesTM Ground Station, and will soon be enhanced with the, for more details):, High speed logging at up to 50Hz (increased from 10Hz).,
Details The OSD Pro is the ultimate on-screen display for ...